DMC TSC-34/RU Specifikace Strana 128
- Strana / 179
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
128 System Software Diagnostics Guide — September 2006
PSTN Diagnostics Tool Reference
26.2 Guidelines
The following restrictions apply to the pstndiag tool:
• The tool is not supported on boards based on Springware architecture.
• It is recommended that you view or monitor no more than 8 channels in your system at one
time. Viewing more than 8 channels at one time may negatively impact system performance.
• The pstndiag tool will only identify and list boards with PSTN front-end interfaces. Boards
that do not have PSTN front-end interfaces (for example, resource only) will not be presented
and cannot be monitored or manipulated by pstndiag.
Pstndiag is a QScript utility. For more information about QScript utilities, refer to Chapter 27,
“QScript Reference”.
26.3 Preparing to Run the PSTN Diagnostics Tool
Before running the pstndiag tool, ensure that you have performed the following tasks:
1. The Intel
®
Dialogic
®
system release software has been properly installed.
2. The Intel Dialogic system has been started for the boards in your system. The pstndiag tool
will detect boards that have already been downloaded.
26.4 Running the PSTN Diagnostics Tool
This section provides instructions for running the pstndiag tool and describes the user interface.
The following topics are covered:
• Starting the PSTN Diagnostics Tool
• The Main Window
• The View Bar
• Option Buttons and Command Buttons
• Keyboard Navigation
26.4.1 Starting the PSTN Diagnostics Tool
This section contains instructions for starting the pstndiag tool in Windows and in Linux.
To start the pstndiag tool in Windows, follow these instructions:
1. Open a command prompt window. The default location of the tool is
%INTEL_DIALOGIC_DIR%\qscript\tools\pstndiag\. However, you can run the tool from any
location.
2. At the command prompt, type:
pstndiag
- Dialogic 1
- System Software 1
- Contents 10
- Revision History 11
- About This Publication 13
- Related Information 15
- Diagnostics Overview 17
- System Requirements 21
- Using the Diagnostics 23
- Management Console (DMC) 23
- 3.4 Viewing a Log File 24
- Checking DM3 Architecture 27
- 4.4 Unsupported Boards 28
- 4.5 Tracing Firmware 28
- Processor Fault on a Board 29
- Diagnosing First Call Issues 31
- 6.1 Preparation 35
- Debugging Software 41
- Failure or Crash 44
- • Windows systems: 45
- Tracing CAS Signaling Using 47
- Global Call 47
- Sample application code 48
- Tracing Multiple ISDN Trunks 55
- Using Global Call 55
- 9.2 Requirements 56
- CallInfo Reference 63
- 10.3 Options 64
- CAS Trace Reference 65
- DebugAngel Reference 69
- Console (DMC) Reference 71
- Diagnostics Management 71
- 13.2 Guidelines 72
- 13.3 DMC Main Window 72
- 13.3.1 Menu Bar 73
- 13.3.3 Log File Panel 73
- 13.4 DMC Configuration Dialog 74
- DigitDetector Reference 77
- Dlgsnapshot Reference 79
- 15.3 Options 80
- 15.3.3 Command Line Options 81
- DM3Insight Reference 83
- DM3post Reference 85
- 17.3 Options 86
- • 02H is CAS data 90
- • 04H is R2MF tone data 90
- • 08H is SigDet ON data 90
- • 10H is SigDet OFF data 90
- 18.4 Payload Formats 91
- 18.5 Sample Parser 94
- GCEV_TRACEDATA Reference 100
- 18.6 Sample Parser Output 102
- Getver Reference 103
- 19.3 Output 104
- ISDN Trace Reference 105
- Summary Tool Reference 107
- Intel Telecom Subsystem 107
- %INTEL_DIALOGIC_DIR%\bin 108
- – Board Memory Dumps 109
- – File Versions 109
- KernelVer Reference 113
- MercMon Reference 115
- 23.3 Options 119
- PDK Trace Reference 121
- 24.3 Options 122
- 24.4 Sample Scenarios 122
- Phone Reference 125
- 26.1 Description 127
- 26.2 Guidelines 128
- 26.4.2 The Main Window 129
- 26.4.3 The View Bar 130
- Channel State Commands 131
- Inbound Call Control Commands 132
- Call Hold Commands 132
- Call Transfer Commands 133
- SendISDN Command 134
- Misc. Commands 134
- 26.4.5 Keyboard Navigation 135
- 26.6 PSTN Diagnostics Menus 136
- 26.6.3 View menu 137
- 26.6.4 Help menu 137
- -openlog c:/temp/test.pdlog 138
- QScript Reference 139
- Single Session Variable 140
- Runtime Trace Facility (RTF) 141
- Reference 141
- 28.2 Installing RTF 142
- 28.3 RTF Configuration File 142
- 28.3.1 RTFConfig Tag 143
- 28.3.2 Logfile Tag 145
- 28.3.3 Global Tag 147
- 28.3.4 GLabel Tag 148
- 28.3.5 GClient Tag 149
- 28.3.6 GClientLabel Tag 149
- 28.3.7 Module Tag 150
- 28.3.8 MLabel Tag 151
- 28.3.9 MClient Tag 152
- 28.3.10 MClientLabel Tag 152
- 28.5 rtftool Command 156
- RTFConfigLinux.xml 157
- RTFConfigWin.xml 158
- Explanation 159
- 28.7.1 Introduction 160
- 28.7.4 Cautions 161
- RTFManager Reference 163
- 29.2 Guidelines 164
- 29.3 Starting RTFManager 164
- 29.4 Main Window 164
- 29.4.1 File 165
- 29.4.2 Edit 165
- 29.5 General Tab 166
- 29.6 Filtering Tab 168
- 29.7 Log File Filtering 170
- 29.8 Advanced Tab 171
- Status Monitor Reference 173
- Glossary 175
- , 55, 89 177
- , 56, 125 178
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.028 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce